RPDG-160B

MEAN WELL
AC-DC сетевой преобразователь - P вых: 150 Вт; Выход: 5 В, 24 В, 5 В SB; U1: 5...5.5 В; I1: 1...12 А; Стабилизация: напряжение; Вход: 110/220В авто
развернуть ▼ свернуть ▲
Фотография серии RPD-160
Чертеж серии RPD-160
 
 

Технические характеристики

показать свернуть
Выходная мощность (ном)
Выход
Напряжение 1 канала
Выходной ток 1 канала
Тип стабилизации
Вход
Конструктивное исполнение
Возможности
Типы защиты КЗ, перегрузка, перенапряжение, перегрев
Количество выходов
Тип управления выходом
Исполнение
Входное напряжение AC
Входное напряжение DC
Коэффициент мощности
Напряжение изоляции вход-выход
Напряжение изоляции вход-земля
Напряжение изоляции выход-земля
Применение
КПД
Шум
Размер 127×76.2×33 мм
Рабочая температура
Нашли ошибку? Выделите её курсором и нажмите CTRL + ENTER

Файлы 1

показать свернуть
RPD-160 160W Dual Output Medical Type series Features : Universal AC input / Full range Built-in active PFC function Protections: Short circuit / Overload / Over voltage / Over temperature 5"x3" compact size Free air convection for 100W and 150W with 20.5 CFM forced air With power good and fail signal output No load power consumption under 0.75W by PS-ON control (G model) Standby 5V@0.8A with fan, @0.6A without fan (G model) 3 years warranty RPD G G: With 5Vsb & no load power consumption < 0.75 W Blank: Basic function (without 5Vsb) 160B EN60601-1 IEC60601-1 SPECIFICATION RPD-160B MODEL OUTPUT NUMBER CH1 CH2 DC VOLTAGE 5V 24V RATED CURRENT (20.5CFM) 12A 3.6A CURRENT RANGE (convection) 1 ~ 6A 0.2 ~ 2.8A CURRENT RANGE (20.5CFM) 1 ~ 12A 0.2 ~ 3.6A RATED POWER (convection) Note.7 100.2W OUTPUT RATED POWER (20.5CFM) Note.8 150.4W RIPPLE & NOISE (max.) Note.2 80mVp-p 200mVp-p VOLTAGE ADJ. RANGE CH1: 5 ~ 5.5V VOLTAGE TOLERANCE Note.3 2.5% LINE REGULATION 0.5% LOAD REGULATION 1.5% Note.6 90 ~ 264VAC 47 ~ 63Hz POWER FACTOR (Typ.) EFFICIENCY (Typ.) PF>0.93/230VAC 84% AC CURRENT (Typ.) INRUSH CURRENT (Typ.) 1.7A/115VAC 0.9A/230VAC COLD START 35A/115VAC 70A/230VAC Earth leakage current <300uA / 264VAC, patient leakage current <100uA/264VAC OVERLOAD 105 ~ 135% rated output power Protection type : Hiccup mode, recovers automatically after fault condition is removed OVER TEMPERATURE WORKING HUMIDITY SAFETY STANDARDS WITHSTAND VOLTAGE (Note 4) NOTE Protection type : Shut down o/p voltage, re-power on to recover 105 (TSW1) detect on heatsink of power transistor 90 (TSW2 ) detect on heatsink of power transistor Protection type : (TSW1)Shut down o/p voltage, recovers automatically after temperature goes down 20 ~ 90% RH non-condensing -40 ~ +85 , 10 ~ 95% RH 0.03%/ (0 ~ 50 ) 10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes UL60601-1, TUV EN60601-1 approved I/P-O/P:4KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC ISOLATION RESISTANCE I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 / 70% RH EMI CONDUCTION & RADIATION Compliance to EN55011 (CISPR11), EN55022 (CISPR22) Class B HARMONIC CURRENT Compliance to EN61000-3-2,-3 EMS IMMUNITY MTBF OTHERS CH1: 5.75 ~ 6.75V Protection type : (TSW2)Shut down o/p voltage, re-power on to recover 5VSB : 5V@0.6A without fan, 0.8A with fan 20.5CFM ; tolerance 2%, ripple : 50mVp-p(max.) 5V STANDBY (G model) PS-ON INPUT SIGNAL (G model) Power on: PS-ON = "Hi" or " > 2 ~ 5V" ; Power off: PS-ON = "Low" or " < 0 ~ 0.5V" PF>1ms POWER GOOD / POWER FAIL 500ms>PG>10ms -20 ~ +70 (Refer to output load derating curve) WORKING TEMP. ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION EMC PF>0.98/115VAC at full load LEAKAGE CURRENT PROTECTION SAFETY & 127 ~ 370VDC FREQUENCY RANGE OVER VOLTAGE FUNCTION 3.0% 2500ms, 30ms/115VAC at full load 16ms/230VAC/115VAC at full load HOLD UP TIME (Typ.) INPUT 1.0% 1200ms, 30ms/230VAC SETUP, RISE TIME VOLTAGE RANGE 6.0% DIMENSION PACKING Compliance to EN61000-4-2,3,4,5,6,8,11; ENV50204, EN55024, EN60601-1-2, EN61204-3, medical level, criteria A 196.3Khrs min. MIL-HDBK-217F (25 ) 127*76.2*34.6mm (L*W*H) 0.33Kg; 36pcs/12.9Kg/0.79CUFT 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. 5. HS1,HS2 & HS3 can not be shorted. 6. Derating may be needed under low input voltages. Please check the derating curve for more details. 7. The rated power includes 5Vsb @ 0.6A. 8. The rated power includes 5Vsb @ 0.8A. PDF
Документация на серию RPD-160 

RPD,RPDG-160.cdr

Дата модификации: 03.06.2009

Размер: 379.9 Кб

2 стр.

    Внимание! Точность указанного на сайте описания товара не может быть гарантирована. Для получения более полной и точной информации о товаре смотрите техническое описание (Datasheet) на сайте производителя.

    AD-155B (MW)