MXC62351QP

MEMSIC
Ultra High Performance 1.5 g Dual Axis Accelerometer with I2C Interface MXC6235xQ FEATURES RoHS compliant VDD TEMP I2C Slave, FAST (≤400 KHz) mode interface 1.8V compatible I/O Ultra Low Noise and initial offset Embedded Power up/down function On-chip temperature sensor available Eight, customer defined 7-bit addresses 2.7 V to 3.6 V single supply continuous operation Monolithic CMOS IC Low...
развернуть ▼ свернуть ▲
 

Технические характеристики

показать свернуть
Рабочие оси
Диапазон измерения
Выходной интерфейс
Напряжение питания
Ток потребления
Рабочая температура
Примечания 5x5x1.55 8pin LCC; Address 22H
Нашли ошибку? Выделите её курсором и нажмите CTRL + ENTER

Файлы 1

показать свернуть
Ultra High Performance 1.5 g Dual Axis Accelerometer with I2C Interface MXC6235xQ FEATURES RoHS compliant VDD TEMP I2C Slave, FAST (≤400 KHz) mode interface 1.8V compatible I/O Ultra Low Noise and initial offset Embedded Power up/down function On-chip temperature sensor available Eight, customer defined 7-bit addresses 2.7 V to 3.6 V single supply continuous operation Monolithic CMOS IC Low power consumption: typically <2 mA @ 3.0 V Resolution better than 1 mg On chip mixed signal processing >50,000 g shock survival rating Low profile LCC package: 5mm X 5mm X 1.55mm Internal Oscillator CLK COM VREF Temperature Sensor CLK No Connection TEMP Coarse Gain Adj. Heater Control Fine Gain Adj. No Connection Temp Comp. X aixs CLK TEMP CLK CLK Fine Gain Adj. Coarse Gain Adj. Temp Comp. Y aixs Acceleration Sensor CLK A/D CLKTEMP IIC Convertor SCL SDA A/D CLK CLK GND APPLICATIONS Security – Gas Line, Elevator, Fatigue Sensing MXC6235xQ FUNCTIONAL BLOCK DIAGRAM Gaming – Joystick, RF Interface, Menu Selection, Tilt Sensing GPS – Electronic Compass Tilt Correction, Dead Reckoning Consumer – LCD Projectors, Pedometers, Blood Pressure Monitor, Digital Cameras Information Appliances – Computer Peripherals, PDA’s, Mouse Smart Pens, Cell Phones GENERAL DESCRIPTION The MXC6235xQ is a low cost, dual axis accelerometer fabricated on a standard, submicron CMOS process. It is a complete sensing system with on-chip mixed signal processing. The MXC6235xQ measures acceleration with a full-scale range of 1.5 g and a sensitivity of 512counts/g at @3.0 V at 25C. It can measure both dynamic acceleration (e.g. vibration) and static acceleration (e.g. gravity). The MXC6235xQ design is based on heat convection and requires no solid proof mass. This design eliminates the stiction problems associated with legacy technologies and provides shock survival greater than 50,000g’s. Information furnished by MEMSIC is believed to be accurate and reliable. However, no responsibility is assumed by MEMSIC for its use, or for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of MEMSIC. MEMSIC MXC6235xQ Rev.C Page 1 of 9 Memsic’s solid state design leads to significantly lower failure rates in customer applications and lower loss due to handling during manufacturing and assembly processes The MXC6235xQ provides I2C digital output with 400 KHz. fast mode operation. The typical noise floor is 0.13 mg/ Hz allowing signals below 0.5mg to be resolved at 1 Hz bandwidth. The MXC6235xQ is packaged in a hermetically sealed, low profile LCC surface mount package (5 mm x 5 mm x 1.55 mm) and is available in operating temperature ranges of 40C to +105C (MXC6235xQB) or -20C to +105C (MXC6235xQP) www.memsic.com 11/30/2010 PDF
Документация на MXC62350QB 

MXC6201Q

Дата модификации: 22.01.2023

Размер: 668.2 Кб

9 стр.

    Внимание! Точность указанного на сайте описания товара не может быть гарантирована. Для получения более полной и точной информации о товаре смотрите техническое описание (Datasheet) на сайте производителя.

    MC3419-P (MEMSIC)