MXA2500EL

Ultra Low Noise, Offset Drift ±1 g Dual Axis Accelerometer with Analog Outputs MXA2500E FEATURES Better than 1 mg resolution Dual axis accelerometer fabricated on a monolithic CMOS IC RoHS compliant On-chip mixed mode signal processing No moving parts 50,000 g shock survival rating 17 Hz bandwidth expandable to >160 Hz 3V to 5.25V single supply continuous operation Small (5mm x 5mm x 2mm) su...
развернуть ▼ свернуть ▲
 

Технические характеристики

показать свернуть
Рабочие оси
Диапазон измерения
Выходной интерфейс
Напряжение питания
Ток потребления
Рабочая температура
Примечания Zero-g offset = 100 mg; 5x5x2 8pin LCC;
Нашли ошибку? Выделите её курсором и нажмите CTRL + ENTER

Файлы 1

показать свернуть
Ultra Low Noise, Offset Drift ±1 g Dual Axis Accelerometer with Analog Outputs MXA2500E FEATURES Better than 1 mg resolution Dual axis accelerometer fabricated on a monolithic CMOS IC RoHS compliant On-chip mixed mode signal processing No moving parts 50,000 g shock survival rating 17 Hz bandwidth expandable to >160 Hz 3V to 5.25V single supply continuous operation Small (5mm x 5mm x 2mm) surface mount package Continuous self test Custom programmable specifications Independent axis programmability (special order) Sck (optional) Internal Oscillator CLK TOUT Voltage Reference VREF Continous Self Test Heater Control X axis Low Pass Filter AOUTX Low Pass Filter AOUTY Factory Adjust Offset & Gain Y axis APPLICATIONS Temperature Sensor 2-AXIS SENSOR Automotive – Vehicle Security/Active Suspension/ABS Headlight Angle Control/Tilt Sensing Security – Gas Line/Elevator/Fatigue Sensing Office Equipment – Computer Peripherals/PDA’s/ Cell Phones Gaming – Joystick/RF Interface/Menu Selection/Tilt Sensing VDD Gnd VDA MXA2500E FUNCTIONAL BLOCK DIAGRAM White Goods – Spin/Vibration Control GENERAL DESCRIPTION The MXA2500E is an ultra low noise and low cost, dual axis accelerometer fabricated on a standard, submicron CMOS process. It is a complete sensing system with onchip mixed mode signal processing. The MXA2500E measures acceleration with a full-scale range of ±1 g and a sensitivity of 500mV/g @5V at 25°C. It can measure both dynamic acceleration (e.g., vibration) and static acceleration (e.g., gravity). The MXA2500E design is based on heat convection and requires no solid proof mass. This eliminates stiction and particle problems associated with competitive devices and provides shock survival of 50,000 g, leading to significantly lower failure rates and lower loss due to handling during assembly. Information furnished by MEMSIC is believed to be accurate and reliable. However, no responsibility is assumed by MEMSIC for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of MEMSIC. MEMSIC MXA2500E Rev G Page 1 of 9 The MXA2500E provides two absolute analog outputs. The typical noise floor is 0.2 mg/ Hz allowing signals below 1 mg to be resolved at 1 Hz bandwidth. The 3dB rolloff of the device occurs at 17 Hz but is expandable to >160 Hz (ref. Application Note AN-00MX-003). The MXA2500E is available in a LCC surface mount package (5 mm x 5 mm x 2 mm). It is hermetically sealed and is operational over a -40°C to +105°C temperature range. It also contains an on-chip temperature sensor and a bandgap voltage reference. Due to the standard CMOS structure of the MXA2500E, additional circuitry can easily be incorporated into custom versions for high volume applications. Contact the factory for more information. MEMSIC, Inc. One Technology Drive Suite 325,Andover MA01810,USA Tel: +1 978 738 0900 Fax: +1 978 738 0196 www.memsic.com 2/26/2007 PDF
Документация на серию MXA2500E 

Microsoft Word - MXA2500E_RevG.doc

Дата модификации: 09.07.2010

Размер: 175.5 Кб

8 стр.

    Внимание! Точность указанного на сайте описания товара не может быть гарантирована. Для получения более полной и точной информации о товаре смотрите техническое описание (Datasheet) на сайте производителя.