Серия Электромеханических реле HG4

Общие характеристики

	Раздел	Реле электромеханические
	Тип контактов
	Номинальный ток коммутации
	Коммутируемое напряжение AC (пиковое)
	Рабочая температура
	Размер	68×36×56 мм
	Способ подключения выводов
	Применение

Документация на серию HG4

HG 20 AMP POWER RELAY 36 1.417 a HG RELAYS FEATURES 56 2.205 HG2 HG3 HG4 mm inch a 34.0 1.339 50.0 1.969 68.0 2.667 • Large capacity — 20 A 250 V AC resistive and 1.5 kW 3 phase 220 V AC motor loads • High contact reliability after long use • Usable with direct soldering, quick-connect and plug-in terminals. (.250) SPECIFICATIONS Contacts Characteristics (at 60 Hz, 20°C 68°F) Arrangement Initial contact resistance, max. (By voltage drop 6 V DC 1A) Contact material Nominal switching capacity Min. switching capacity#1 2 Form C, 3 Form C, 4 Form C 15 mΩ Silver alloy 20 A 250 V AC (resistive) 100 mA, 5 V DC Expected life (min. operations) Mechanical (at 180 cpm) AC type: 107, DC type: 106 Life curve for AC types 4 Operations, ×10 900 Functional*4 Shock resistance Mechanical life : 107 Operating frequency: 180 op./min. 1,000 Maximum operating speed Initial insulation resistance*1 Between open contacts Initial Between contacts sets breakdown voltage*2 Between contacts and coil 2 Form C type Operate time*3 (approx.) 3 Form C & (at nominal voltage) 4 Form C type 2 Form C type Release time (without diode)*3 (approx.) 3 Form C & (at nominal voltage) 4 Form C type Destructive*5 800 Functional*6 700 Vibration resistance Destructive 600 500 Ambient Conditions for operation, temp. transport and storage*7 (Not freezing and condensing at Humidity low temperature) 2 Form C type Unit weight 3 Form C type 4 Form C type 400 300 100 0 25 200 125 V A 0 C cosϕ VA C co s 5 ϕ=1 10 =1 15 20 Load current, A #1 This value can change due to the switching frequency, environmental conditions, and desired reliability level, therefore it is recommended to check this with the actual load. Remarks * Specifications will vary with foreign standards certification ratings. *1 Measurement at same location as “Initial breakdown voltage” section 20 cpm Min. 100 MΩ at 500 V DC 2,000 Vrms for 1 min. 2,000 Vrms for 1 min. 2,000 Vrms for 1 min. Max. 30 ms Max. 40 ms Max. 30 ms Max. 40 ms 98 m/s2 {10 G} (except for the contact moving direction) 980 m/s2 {100 G} 10 to 55 Hz at 1 mm double amplitude 10 to 55 Hz at 2 mm double amplitude –50°C to +40°C –58°F to +104°F 5 to 85% R.H. Approx. 130 g 4.59 oz Approx. 185 g 6.53 oz Approx. 240 g 8.47 oz *2 Detection current: 10 mA *3 Excluding contact bounce time *4 Half-wave pulse of sine wave: 11ms; detection time: 10µs *5 Half-wave pulse of sine wave: 6ms *6 Detection time: 10µs *7 Refer to 6. Conditions for operation, transport and storage mentioned in AMBIENT ENVIRONMENT Electrical life with AC load AC load Voltage, V AC 125 Resistive (cos ϕ ] 1) Inductive (cos ϕ ] 0.4) 250 125 250 Current, A 20 15 20 15 10 15 10 10 7.5 Expected life (min. operations) 5×105 7.5×105 2×105 5×105 7.5×105 2×105 5×105 2×105 5×105 AC load Voltage, V AC Lamp 125 Motor Single phase Three phase 125 250 250 Capacity, kW 0.5 0.3 0.75 0.4 0.75 0.4 1.5 0.75 Expected life (min. operations) 2×105 5×105 2×105 5×105 2×105 5×105 2×105 5×105 Note: In case of an electromagnet or exiting coil load (solenoid, etc.), the value of the motor or lamp load is applicable. Electrical life with DC load DC load Resistive Inductive (L/R ] 7 ms) Voltage, V DC 24 125 24 125 Current, A 15 0.8 10 0.4 Note: For DC inductive load, use of an arc extinguishing circuit is recommended. All Rights Reserved © COPYRIGHT Matsushita Electric Works, Ltd. Expected life (min. operations) 5×105 5×105 5×105 5×105  PDF

Документация на HG2-AC12V 

Дата модификации: 18.10.2005

Размер: 216.8 Кб

5 стр.

• найти HG4.pdf

Товары серии HG4

Наименование	i	Упаковка	AC-DC	Pупр(max)	Магнитная система	Uкатушки
HG4-AC12V (PAN)						—
HG4-AC48V (PAN)						—
HG4-DC24V (PAN)
HG4-DC48V (PAN)
HG4-DC6V (PAN)