Серия DC-DC модульных преобразователей K12T-6A

Mornsun

Общие характеристики

 Раздел DC-DC модульные преобразователи
Монтаж
Выходная мощность
Количество каналов
Входное напряжение
Параметры выходов
Возможности
Комплекс защит от пониженного входного напряжения, перегрузки, КЗ
Номинальное входное напряжение
Напряжение 1 выхода
Ток 1 выхода
КПД
Напряжение изоляции вход-выход
Размер 20.3×11.4×6.6 мм
Рабочая температура

Документация на серию K12T-6A

DC/DC Converter K12T-6A Series Non-isolated & regulated 6A single output FEATURES POL power converter  High efficiency up to 94%  Operating ambient temperature range: -40℃ to +85℃  Input under-voltage protection, output short-circuit, over-current protection  High-speed transient response  Compact SMD package  EN62368 approved RoHS K12T-6A series is a 6A non-isolated switching regulator. The output voltage is accurately adjustable from 0.75V to 5.0V, and the product is featured with high efficiency, fast transient response, input under-voltage, output short circuit, over-current protection. They meet CLASS B of CISPR32/EN55032 EMI standards by adding the recommended external components and they are widely used in applications such as communications, computer network industry, power distributed architecture, workstations, servers, LANs/WANs and provide high current with fast transient response for high-speed chips such as FPGA, DSP, and ASIC. Selection Guide Input Voltage (VDC) Certification CE Part No. ① Nominal (Range) K12T-6A-P 12 K12T-6A-N (8.3~14) Output Max. Voltage(VDC) (Range) 15 0.75~5.0 ② ③ Current (A) Max./Min. 6/0 Capacitive Load(µF) Max. Efficiency(%) Min./Typ. 1mΩ≤ESR <10 mΩ ESR≥10 mΩ 90/94 1000 3000 Notes: ① “P” indicates that the Ctrl pin is positive logic control, “N” indicates that the Ctrl pin is negative logic control; ② Exceeding the maximum input voltage may cause permanent damage; ③ The default output voltage is 0.75VDC, which can be adjusted to 1.2VDC, 1.8VDC, 2.5VDC, 3.3VDC, 5VDC. See Trim instructions for specific output voltage adjustment; ④Unless otherwise specified, parameters in this table were measured under the 5VDC output voltage. Input Specifications Item Operating Conditions Min. Typ. Max. Unit Input Current (full load/no-load) Nominal input voltage -- 2660/20 -- mA Start-up Voltage -- -- 8 Under-voltage Protection 6 -- -- Reverse Polarity Input Avoid / Not protected Hot Plug Unavailable Input Filter Capacitance filter K12T-6A-P (Positive logic) Module on Ctrl* VDC Module off Ctrl pin open or pulled high (Vin-2.5V ~ Vin) K12T-6A-N (Negative logic) Ctrl pin open or pulled low to GND (0 ~ 0.5VDC) K12T-6A-P (Positive logic) Ctrl pin pulled low to GND (0 ~ 0.5VDC) Ctrl pin pulled high (Vin-2.5V ~ Vin) K12T-6A-N (Negative logic) Input current when off -- 1 -- mA Min. Typ. Max. Unit Notes: * 1. The Ctrl pin voltage is referenced to GND; 2. Unless otherwise specified, parameters in this table were measured under the 5VDC output voltage. Output Specifications Item Operating Conditions Voltage Accuracy Full load, nominal input voltage -- ±1.0 ±2.0 Linear Regulation Full load, input voltage range -- ±0.3 -- Load Regulation Nominal input, 0% -100% load -- ±0.4 -- 2021.03.09-A/3 % Page 1 of 5 MORNSUN Guangzhou Science & Technology Co., Ltd. reserves the copyright and right of final interpretation PDF
Документация на серию K12T-6A 

K12T-6A Series Keywords:

Дата модификации: 18.03.2022

Размер: 2.19 Мб

5 стр.

    Товары серии K12T-6A

    Наименование i Упаковка
    K12T-6A-N (MORNSUN)
     
    		в ленте 50 шт
    K12T-6A-P (MORNSUN)
     
    		в ленте 25 шт